|
-
m2 SSD Sata III corrupt?
128gb drive in case almost full all of a sudden didnt show up anymore.
cleaned all contacts and doublechecked box/case. new stick working.
when i checked again it wants to initialyze wrong data-system (gpt) .windows 10 here.
1tb.SSD.^
will now check on other ultrabook.
is this a task for testdisk? older data saved.
if testdisk is needed is it avised to run it from a stick. then i cannot do on this speedy ultrabook since no access to cmos setup-defective screeen and keyboard. must use slower ultrabook.
thanks a lot
Last edited by europanorama; 11-30-2022 at 06:50 AM.
-
after cleaning contacts and trying on other ultrabook this is what diskmanagement is telling.
i have a second M.2 Sata III SSD -stick of identical size to recover data with testdisk.
should i try first with photorec?
Since i know it could last quite a lot of time, would it be better using slower seldom used celeron 4/64? there i could run app from stick. Thanks a lot
its asking for initialization. errors coming trying GPT or MBR
datenträgerinitialisierung.jpg
Easeus? datasaver? do i have to fear nothing?
https://www.easeus.de/festplatte-wie...t-erkannt.html
Last edited by europanorama; 12-01-2022 at 06:07 AM.
-
must run testdisk since easeus wants pinke pinke.
-
-
How about restoro by Microsoft?
https://www.restoro.com/pricing/
-
M2 to be set in Bios? if use externally certainly not. worked in the past.
https://www.easeus.de/festplatte-wie...t-erkannt.html
which alternative software beside easeus?
partition master freebe them installed.
-
Did what advised. Rightclick and set GPT not working MBR tried: again severe hardware-error.
unrepairable stick?
-
https://icybox.de/
No more clonestations. new tech second quarter 2023.
means there were problems. good i didnt start yet cloning.
he advised IB 1817 for datatransfer.
Forgot to tell: M2. SATA III SSD 128 is almost full. maybe made mistake when removing with rules.
good data was evacuated only few data added.
-
dual sata/nvme-station
https://www.youtube.com/watch?v=OVmMn97y2ZA
at least data-transfer if cloning different versions nonworking.
i think new cloning stations coming since a lot of problems making sticks bootable.
lindy SATA/NVMe dual NONAVAILABLE see above
https://www.amazon.de/dp/B0BHWFY67F
available
https://www.amazon.de/dp/B0BHWFY67F
Last edited by europanorama; 12-03-2022 at 10:49 AM.
-
New Icybox clone station isnt direct. its M2 Sata/NVMe SSD to SSD only. model follows
 Originally Posted by europanorama
https://icybox.de/
No more clonestations. new tech second quarter 2023.
means there were problems. good i didnt start yet cloning.
he advised IB 1817 for datatransfer.
Forgot to tell: M2. SATA III SSD 128 is almost full. maybe made mistake when removing with rules.
good data was evacuated only few data added.
New Icybox clone station isnt direct. its M2 Sata/NVMe SSD to SSD only. model follows
i switched to old bootdrive to save data. and this one has also nonaccessible data. see other thread. maybe attacked maybe since forgot to clean also innercontacts under board. they looked worn out.
ist uncommon that both main storages used are corrupt. dont know when i switched from stick to Sata-HDD. see new thread about testdisk and recuva recovery. stick is silent. no light there. maybe fake intenso. its not Top version Sata III. image follows.
-
-
I have already the right cloning-station for NVMe.
ICY BOX IB-2912MCL-C31
will not test if cloning removable stick is working. will do when i have a new pc.
But i could clone also when stick stays inside.
Got answer about cross-cloning. should work if software-based.
and these station will certainly come. maybe hardware-based cloning then.
But main problem is now accessing Sata-stick. which other partition managers.
from trueimage-seller?
It says hardware error.
could it be sabotage?
netbook will not shutdown when unused. maybe i must set it back.
-
I am about to get new Sata- sticks 512 gb. and clonestation SATA and universal psu 12v 3A seems right. 1.A also working i think. original one piece -bad no quality. had it always under power!!! no switch to turn it down. higest time to install multi-switch power-hub on table. actual one is on wrong table.
-
maybe this will help
https://4ddig.tenorshare.com/hard-dr...ndows-10.html§
could you administrator pls move this thread to the right section?
thanks a lot
-
Which section? This one looks good.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
|
Reply With Quote