Results 1 to 6 of 6

Thread: Weird memory issue

Hybrid View

  1. #1
    Member Aviator_14's Avatar
    Join Date
    Aug 2006
    Location
    California, USA
    Posts
    215

    Weird memory issue

    I upgraded the RAM in a friend's old Dell Dimension 3100 with Windows XP. It was really slow because it only had 256mb of RAM installed. I upgraded it with (2) 512MB sticks of DDR2-533 RAM, and after putting the RAM in and turning on the system I notice that the system restarts multiple times and is unable to fully boot. One time I even got a BSOD. I immediately suspect that the memory I installed was defective.

    I then ran memtest, one stick at a time in the same memory slot (the bottom slot), and both sticks successfully completed the test without any errors; However when I ran memtest with both sticks of memory at the same time in both memory slots, Memtest was really slow and kept looping back to 0%, and after a while came up with an error that said "unexpected interrupt - Halting," and the system freezes.

    At this point I suspect that the motherboard or memory slot on the motherboard is defective, since each RAM stick passes in one slot, but not in both slots.

    But, when I put the original RAM back in (a single 256MB module) it passes Memtest in either the bottom or top slot. At this point I am totally stumped and don't know whether the problem is with the memory or the motherboard.

    Could it be that the computer is picky with what RAM is inserted even though it is compatible?
    See no evil, hear no evil, speak no evil

  2. #2
    Lifetime Friend of Staff
    Join Date
    May 2007
    Location
    Sheboygan, WI
    Posts
    3,921
    Those 2 sticks are not close enough if manufacturers tolerances.

    What crucial says.
    http://www.crucial.com/store/listpar...203100&Cat=RAM

    Why I always buy a new matched set of ram.

    Mismatch can cause:
    1. A no boot situation
    2. All kinds of hair pulling errors
    3. What we want. It works just fine.

  3. #3
    Senior Member rockinup1231's Avatar
    Join Date
    May 2006
    Location
    Northern Michigan
    Posts
    942
    OEM workstations like those tend to be very fickle about the RAM they will accept. Typically speaking, the RAM you installed is the correct kind for that workstation. However, a number of different factors (supported voltage, timing, high or low density, etc.) the memory controller was not designed to handle could cause problems.

    Another thing that comes into play when two sticks of RAM are installed is dual channel mode, which could have additional implications for the stability of the system, especially if either DIMM was manufactured by a different entity.

    So you might try matching DIMM's if you aren't already doing so, or find more known good, similar memory to try as a pair in that machine.
    MSI 870S-G46 | AMD Phenom II X4 965 @ 3.8ghz | Gigabyte Radeon 7870 Ghz Edition | 1 x 128GB Kingston HyperX SSD | 2 x WD 500GB Blue HDD | Arch Linux x64 | BFG Tech LS SERIES LS-550 550W | 2 x 4GB DDR3 1600 RAM, 2 x 2GB DDR3 1600 RAM (12 GB)

  4. #4
    Member Aviator_14's Avatar
    Join Date
    Aug 2006
    Location
    California, USA
    Posts
    215
    The 2 RAM sticks are from the same manufacturer and have the same part number.
    See no evil, hear no evil, speak no evil

  5. #5
    Senior Member rockinup1231's Avatar
    Join Date
    May 2006
    Location
    Northern Michigan
    Posts
    942
    Then you will want to find RAM the motherboard certainly supports. With Dell that is usually Crucial but it can vary. A quick google search should give you some ideas.
    MSI 870S-G46 | AMD Phenom II X4 965 @ 3.8ghz | Gigabyte Radeon 7870 Ghz Edition | 1 x 128GB Kingston HyperX SSD | 2 x WD 500GB Blue HDD | Arch Linux x64 | BFG Tech LS SERIES LS-550 550W | 2 x 4GB DDR3 1600 RAM, 2 x 2GB DDR3 1600 RAM (12 GB)

  6. #6
    Stark Raving MOD Midknyte's Avatar
    Join Date
    May 2002
    Location
    Arkham Asylum
    Posts
    22,270
    Did you check for a bios update? Sometimes that helps with ram compatibility.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •