Results 1 to 8 of 8

Thread: Peltier Qustions

  1. #1
    Member
    Join Date
    Jan 2004
    Location
    Pensacola FL
    Posts
    78

    Peltier Qustions

    What would be your main concern about peltier cooling besides how much power they suck up and the condesation?? I was wanting one for my P4C 2.4 but wasnt sure... would it be good for a comp that stays on 24/7?? is there a thing of a processor gettin too cold?? and where would i get the cold plate and water block for one?? thanks

  2. #2
    Senior Member computer_kid1's Avatar
    Join Date
    Mar 2003
    Location
    UK
    Posts
    600
    try searching peltier cooling in google!
    i found this
    http://www.overclockers.com/articles578/
    theres some info on peltiers on page 3
    http://www.overclockers.com/articles578/index03.asp

  3. #3
    Stark Raving MOD Midknyte's Avatar
    Join Date
    May 2002
    Location
    Arkham Asylum
    Posts
    22,270
    i really wouldn't recommend a peltier in a place as humid as Florida. your dew point is much higher than other places. that means condensation happens at a higher temp. water + cpu = death

    You need to have extra case fans to get rid of the heat that the peltier produces.

    I think you would be better off with just a plain water cooling system if anything.

  4. #4
    Ultimate Member mobo57's Avatar
    Join Date
    Jun 2003
    Location
    In a So Cal Tube
    Posts
    1,971
    If you are really interested, here is a TCM already to go. check this site and the SubZero4G
    http://www.1coolpc.com/
    Profanity: a weak mind trying to express itself forcibly.
    http://www.thegopnet.com

  5. #5
    Member
    Join Date
    Jan 2004
    Location
    Pensacola FL
    Posts
    78
    i am going water cool... but as i was searching for a water block i seen swiftech had one with a peltier in it... interested me so i did a search and seen a DIY peltier setup... to take care of the condsation, he used RTV silicon, Neoprene, and Conformal.. but he had a water block and a cold plate for the peltier but he didnt mention where he got it from.... anyone know where i can get one?? also he really didnt mention much about a power supply for it.. i know they suck alot juice so a bigger power supply woud be needed... i can just plug it into my CPU PSU right?? also is it good for a comp that runs 24/7??? will it get too cold? below zero?

  6. #6
    Member
    Join Date
    Jan 2004
    Location
    Pensacola FL
    Posts
    78
    ???

  7. #7
    Ultimate Member Giblet Plus!'s Avatar
    Join Date
    May 2002
    Location
    Evanston, IL
    Posts
    2,821
    Peltiers are only a little better than great watercooling. I would recommend researching good watercooling setups and putting one of them together first.

    The www.overclockers.com forums and www.procooling.com are great resources.

    PM me with questions, I don't stop in here a lot.
    This is where my signature would go if I wasn't so lazy.

  8. #8
    Senior Member Happy Joe's Avatar
    Join Date
    Nov 2003
    Location
    Colorado
    Posts
    825
    If you want to get subzero temps you need phase change cooling (a refrigerator for your CPU). Its very expensive. It is possible to "roll your own" (Yes, BigJakk, I'm still looking at my dehumidifier with evil thoughts) but you need to be intemately acquainted with refrigeration systems. If you don't know how to braze/silver solder or charge a corpressor I'd avoid the home grown angle. Condensation is still a huge concern, especially in Florida.
    If you want to buy a setup search for Prometeia or Vaporchill.
    http://kit-tronics.com
    Enjoy!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •