POST YOUR 3DMARK2001 SCORES!!!!

[badgern]

P4 2.2 Geforce 4200Ti 512DDR 3D2001 = 9085
P3 800 Geforce 3 200Ti 512SDR 3D2001 = 3200
P2 400 Geforce 4MX440 512SDR 3D2001 = 1475

[Tanelusa]

Ok is this score a bit LOW for me or is it ok?I think its ok!

AmdXp1700
ATI8500LE
196MbSDRAM
40gb 7200rpm
WinXP

Score was:7202

??????????????????????????????????????

[pandaz3]

Originally posted by Tanelusa
Ok is this score a bit LOW for me or is it ok?I think its ok!

AmdXp1700
ATI8500LE
196MbSDRAM
40gb 7200rpm
WinXP

Score was:7202

??????????????????????????????????????

First it is in line, second if its okay with you, then by all means it's okay!

[omega31]

Ok, 2 sets of new scores for me. My P3 system used to have a gf3 ti200, but I yanked it out and put in an original geforce with 32mb sdram. I put the gf3 ti200 in my new XP 1600+ system. Previous score for P3 with gf3 was 4359. Gained 2000 points going from P3 750 to XP 1600+.

P3 750mhz
320mb PC100
Geforce 32mb sdram

3DMark Score 2066
Game 1 - Car Chase - Low Detail 35.8 fps
Game 1 - Car Chase - High Detail 13.9 fps
Game 2 - Dragothic - Low Detail 34.7 fps
Game 2 - Dragothic - High Detail 17.0 fps
Game 3 - Lobby - Low Detail 35.5 fps
Game 3 - Lobby - High Detail 19.5 fps
Game 4 - Nature Not supported by hardware
Fill Rate (Single-Texturing) 161.8 MTexels/s
Fill Rate (Multi-Texturing) 318.1 MTexels/s
High Polygon Count (1 Light) 10.2 MTriangles/s
High Polygon Count (8 Lights) 2.7 MTriangles/s
Environment Bump Mapping Not supported by hardware
DOT3 Bump Mapping 22.1 fps
Vertex Shader 19.8 fps
Pixel Shader Not supported by hardware
Advanced Pixel Shader Not supported by hardware
Point Sprites 5.1 MSprites/s


Athlon XP 1600+
ECS K7S5A
512mb PC2100

3DMark Score 6438
Game 1 - Car Chase - Low Detail 97.9 fps
Game 1 - Car Chase - High Detail 41.9 fps
Game 2 - Dragothic - Low Detail 93.8 fps
Game 2 - Dragothic - High Detail 51.9 fps
Game 3 - Lobby - Low Detail 103.0 fps
Game 3 - Lobby - High Detail 50.1 fps
Game 4 - Nature 30.6 fps
Fill Rate (Single-Texturing) 586.0 MTexels/s
Fill Rate (Multi-Texturing) 1213.0 MTexels/s
High Polygon Count (1 Light) 20.2 MTriangles/s
High Polygon Count (8 Lights) 4.5 MTriangles/s
Environment Bump Mapping 100.2 fps
DOT3 Bump Mapping 89.9 fps
Vertex Shader 57.2 fps
Pixel Shader 67.9 fps
Advanced Pixel Shader 54.2 fps
Point Sprites 13.0 MSprites/s

P3 drop from 4359 to 2066. The 4359 score was using Win2k. The other scores are in Win98se. I'll install Win2k on my new system when I have time. Also need to tweak some settings on Win98se. Haven't tweaked it as much as my older system, since the new is only a week old.

[Giblet Plus!]

11296 3D marks

MSI ti4200 64 mb @ 310 mhz core 600 memory

Amd XP2000 @ 145 fsb (1825 mhz)

MSI KT3 Ultra (kt333)

256 mb ddr2100 cas 2 (haven't unlocked the xp yet, and asynch mode sucks so the ddr stays at 2100 speeds)

Pretty good for such a cheap video card!

[Witch-Talon]

How can u overclock your AMD XP2000 if you haven't unlock it???

Originally posted by Giblet Plus!
11296 3D marks

MSI ti4200 64 mb @ 310 mhz core 600 memory

Amd XP2000 @ 145 fsb (1825 mhz)

MSI KT3 Ultra (kt333)

256 mb ddr2100 cas 2 (haven't unlocked the xp yet, and asynch mode sucks so the ddr stays at 2100 speeds)

Pretty good for such a cheap video card!

[x51out]

You can overclock a CPU by increasing the multiplier or front side bus or a combination of the two. Obviously, since he has left the CPU locked (at 12.5) he cannot raise the multiplier, it stays at 12.5 all the time. But he can raise the fsb from the default 133 (12.5x133=1666) to 12.5x146=1825mhz. I get better results by increasing the fsb more than by increasing the multiplier. Reason: the multiplier only increases the CPU speed, whereas the fsb increase effects all buses (agp/pci and ram) therefore increasing overall system speed. But will also crash your whole system if taken too far.

[Witch-Talon]

Never overclocked an AMD CPU. Did't know you did't have to unlock the CPU to be able Increase FSB. I've only overclocked P4 CPU never AMD CPU. Thanks for explaining.

Originally posted by x51out
You can overclock a CPU by increasing the multiplier or front side bus or a combination of the two. Obviously, since he has left the CPU locked (at 12.5) he cannot raise the multiplier, it stays at 12.5 all the time. But he can raise the fsb from the default 133 (12.5x133=1666) to 12.5x146=1825mhz. I get better results by increasing the fsb more than by increasing the multiplier. Reason: the multiplier only increases the CPU speed, whereas the fsb increase effects all buses (agp/pci and ram) therefore increasing overall system speed. But will also crash your whole system if taken too far.

[Bizkitkid2001]

Originally posted by Witch-Talon
Never overclocked an AMD CPU. Did't know you did't have to unlock the CPU to be able Increase FSB. I've only overclocked P4 CPU never AMD CPU. Thanks for explaining.

You can OC any amd by the FSB. But certain AMDs have to be unlock to change the multiplier. The only two AMD cpus that I know of that con UNlocked are the 1.2 and 1.4ghz T'Bird.

[Witch-Talon]

One negative thing about FSB O/Cing is it mess up the USB Devices.

Originally posted by Bizkitkid2001




You can OC any amd by the FSB. But certain AMDs have to be unlock to change the multiplier. The only two AMD cpus that I know of that con UNlocked are the 1.2 and 1.4ghz T'Bird.

[Bigjakkstaffa]

You can OC any amd by the FSB. But certain AMDs have to be unlock to change the multiplier. The only two AMD cpus that I know of that con UNlocked are the 1.2 and 1.4ghz T'Bird.

My 1.33ghz Tbird came unlocked for my o/c'ing pleasures.. shame i can only get the bugger up to 1.47

--Jakk

[Witch-Talon]

Increase the multiplier and push more voltage if needed.

Originally posted by Bigjakkstaffa


My 1.33ghz Tbird came unlocked for my o/c'ing pleasures.. shame i can only get the bugger up to 1.47

--Jakk

[Bigjakkstaffa]

Taht is with the multiplier and voltage dont help none

--Jakk

[Witch-Talon]

Voltage arent suppose to give addontial speed all it does is give cpu more power to handle higher O/C speed. maybe it's due to the mainboard limit? Few FSB speed choices and dont have high multiplier ablity.

Originally posted by Bigjakkstaffa
Taht is with the multiplier and voltage dont help none

--Jakk

[x51out]

Witch-Talon, he just wrote that his cpu was unlocked. Dude. His 1333 T-Bird was 10x133 at default, and he most likely did 10.5x140, or even 11x133 (which wouldn't really make any sense though). Jack, 137 mhz increase aint too shabby, considering the T-Bird core at our end. I can push my AYHJA 1400 T-Bird to 1596, but after that all bets are off. That is roughly the same increase as you 137/159, that is pretty close. Best boost is with fsb though.