Page 1 of 5 1 2 3 4 5 LastLast
Results 1 to 15 of 71

Thread: TBredA... 1.95GHz on air!!

  1. 12-29-2002, 04:23 AM #1
    causticVapor
    causticVapor is offline
    Ultimate Member
    Join Date
    Aug 2002
    Posts
    3,922

    TBredA... 1.95GHz on air!!

    Yes, tis true Sirs and Madams.... I've been able to achieve 1.95GHz on air with nothing but an Al heatsink and a lot of air! (And a vmod on the 8-KHA+ to get the core up to 1.9v...)

    Just installed in my dad's case... the first time this CPU has not been on water... but it's doing just fine with...

    The most crazy combination 'tis... an inhell tualatin HSF with a secondary zalman 92mm fan feeding air at full speed to the nidec fan! (Case open)

    41C idle
    50C maxload


    1.53GHz XP 1800+ TbredA @ 1.95GHz XP 2350+ (156*12.5) -- 1.9v (stable)
    166*12 2.0GHz 2400+ (boots but freezes at the desktop, not a mem prob, will run @ 175 forever with lower CPU speed; a temp prob I think)


    512MB 266MHz CL2.5 DDR @ 2.5, 2-2-6, 312MHz -- 2.9v
    Antec 350W SmartPower PSU
    64MB Ti 4200 -- not OCd yet, feel like there is an interface problem...
    and 5 PCI slots filled!





    Will get 3dmark2001se installed soon... the network's all f-d up so sorry for the delays
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  2. 12-29-2002, 04:24 AM #2
    causticVapor
    causticVapor is offline
    Ultimate Member
    Join Date
    Aug 2002
    Posts
    3,922
    Here's the Sandra arithmetic results........
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  3. 12-29-2002, 04:25 AM #3
    causticVapor
    causticVapor is offline
    Ultimate Member
    Join Date
    Aug 2002
    Posts
    3,922
    ...Multimedia....
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  4. 12-29-2002, 04:29 AM #4
    causticVapor
    causticVapor is offline
    Ultimate Member
    Join Date
    Aug 2002
    Posts
    3,922
    ...and memory bandwidth. Note it's on the lower side... had stuff running.
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  5. 12-29-2002, 06:54 AM #5
    Grentarc
    Grentarc is offline
    Senior Member Grentarc's Avatar
    Join Date
    Feb 2002
    Location
    Wagga, NSW, Australia
    Posts
    759
    is that a challenge causticVapour????
    I will see what i can do on my board with air. . as i am not running at full voltage yet (may still have to do a voltage mod to mine)
    I think i am about as high as possible on FSB, but i can still multiplier it up there!
    i will post again later if i decide to 1.95 my 1700+ T-Bred A
    Reply With Quote Reply With Quote
  6. 12-29-2002, 07:26 AM #6
    Grentarc
    Grentarc is offline
    Senior Member Grentarc's Avatar
    Join Date
    Feb 2002
    Location
    Wagga, NSW, Australia
    Posts
    759
    I cant hit 2 GHz without a Vmod to my board, and i dont want to drop my FSB lower than 166, so i have 11.5x 167 at the moment.
    ahh well... CONGRATS on the OC!
    Reply With Quote Reply With Quote
  7. 12-29-2002, 08:19 PM #7
    ConfusedAlien
    ConfusedAlien is offline
    Ultimate Member ConfusedAlien's Avatar
    Join Date
    Dec 2001
    Location
    In Your anubis
    Posts
    1,129
    jeez, how long do you expect the chip to last?
    like 2 years? how much you can crank out of it?
    id like to know what i could do, theoretically, with xp 2000+

    whats the best xp to crank?
    the thoroughbred or reg.
    i heard 2400+ was good
    Reply With Quote Reply With Quote
  8. 12-30-2002, 12:42 AM #8
    Giblet Plus!
    Giblet Plus! is offline
    Ultimate Member Giblet Plus!'s Avatar
    Join Date
    May 2002
    Location
    Evanston, IL
    Posts
    2,821
    Once I get my h20 setup up and running I might be able to hit 1.95 ghz on my palimino!
    This is where my signature would go if I wasn't so lazy.
    Reply With Quote Reply With Quote
  9. 12-30-2002, 09:53 PM #9
    causticVapor
    causticVapor is offline
    Ultimate Member
    Join Date
    Aug 2002
    Posts
    3,922
    With the vmod I would have been able to push 2v into the palomino and hit 2GHz; now I'll never know.
    Reply With Quote Reply With Quote
  10. 12-30-2002, 09:55 PM #10
    Giblet Plus!
    Giblet Plus! is offline
    Ultimate Member Giblet Plus!'s Avatar
    Join Date
    May 2002
    Location
    Evanston, IL
    Posts
    2,821
    poor baby. I'm working with 1.85V max at the moment. I'm hoping my future h20 setup will get me to 1.95 ghz.
    This is where my signature would go if I wasn't so lazy.
    Reply With Quote Reply With Quote
  11. 12-30-2002, 11:39 PM #11
    causticVapor
    causticVapor is offline
    Ultimate Member
    Join Date
    Aug 2002
    Posts
    3,922
    Hopeless....
    Reply With Quote Reply With Quote
  12. 12-31-2002, 01:04 AM #12
    Giblet Plus!
    Giblet Plus! is offline
    Ultimate Member Giblet Plus!'s Avatar
    Join Date
    May 2002
    Location
    Evanston, IL
    Posts
    2,821
    I sense a mocking tone. . . .
    This is where my signature would go if I wasn't so lazy.
    Reply With Quote Reply With Quote
  13. 12-31-2002, 05:17 AM #13
    causticVapor
    causticVapor is offline
    Ultimate Member
    Join Date
    Aug 2002
    Posts
    3,922
    ...without a voltage mod. *Hands his 25W soldering iron and a 240KÙ resistor to GP*
    Reply With Quote Reply With Quote
  14. 12-31-2002, 08:24 AM #14
    causticVapor
    causticVapor is offline
    Ultimate Member
    Join Date
    Aug 2002
    Posts
    3,922
    I'm having problems overclocking the card beyond 275 core, but the mem will go just fine And 164 FSB has been attained, with the cpu at 1.97GHz.

    http://service.futuremark.com/compare?2k1=5493100
    Reply With Quote Reply With Quote
  15. 12-31-2002, 02:34 PM #15
    Giblet Plus!
    Giblet Plus! is offline
    Ultimate Member Giblet Plus!'s Avatar
    Join Date
    May 2002
    Location
    Evanston, IL
    Posts
    2,821
    My cooling will be a bit better than yours, and the cpu has been to 1.87 ghz @ 1.8V already. . .
    This is where my signature would go if I wasn't so lazy.
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules