IO read data port ISA PnP enumerator Conflicts

[StarWatcher]

I have a problem-I keep getting fatal exceptions{BSOD} Specifically:Exception OE at 0028:C001539A in VxD----called from 002:C183A044 in VxD. I am also getting frequent PnP fatal exceptions.

I have checked all the Windows help sites {Nathans too} and Microsoft library -can't find a match for this exception.

But, I found a conflict in system-device manager-system devices:IO read data port for ISA Plug and Play enumerator Under the resource tab it says-"The resources this device is using does not match any of its known configurations. To assign resources manually for this device click Configuration Manually"

Two conflicting devices are listed 1. Input\output range 0374-0377 used by secondary IDE controller{dual fifo}and 2. Input\output range 0374-0377 used by Intel 82371AB\EB PCI Bus master IDE Controller.

And under Resources type -Input\Output Range 0374-0377 has a red circle with a line through it.

I am running W98-64MB SDRAM-351 CPU-Award Bios v.4.51 PG(7-21-98)

What exact changes to I have to make to the CMOS\Bios configurations?

Thank You in advavce http://www.sysopt.com/forum/smile.gif

[This message has been edited by StarWatcher (edited 05-21-99).]

[This message has been edited by StarWatcher (edited 05-21-99).]

[This message has been edited by StarWatcher (edited 05-23-99).]

[ENVY]

Need more info,is this a socket 7 system or a slot system?Sounds like you need to install the proper drivers for the controllers.Also might try disabling any ports you are not using in the bios,serial and parallel.Is your bios set to plug and play os?Make sure that you do not have any irq's on reserve.The red circle means that device is disabled.Pls give us the motherboard type,cpu,hardrives,etc.

[StarWatcher]

Ok Envy here its is:
1. Clone system-64DRAM-W98
2. HD-generic IDE disk type 46-6GB(Quantum)
Drive type-IDE\EIDE
Controller-Primary IDE controller
(dual fifo)
IDE Device Configuration-Master
DMA Transfers enabled-yes
3. CD-ROM-Atapi-36x
4. Floppy-Generic NEC-1.44MB-3.5
5. Zip drive Iomega 100-96MB
6. CPU\Processors-Intel Pentium II 350Mhz
Mainboard type-Single processor
Type-standard
Co-Processor(FPU)-built in
Model Info.-P6L(Deschutes)PentiumII 333- 450 2.ov
7. Bios- Award Modular v4.51PG
PnP version 1.00
ID#- FC 01 00
8. MOBO-Manufacturer-Wintec(Edom)
Name-W6BXA-O-Intel 440BX-Pentium II
AGP
Chipset-Intel440BX:82443BX\82371EB(PIIX4E)
Serial #07-211998-i440BX-W977TF-2A69KW09C-
02
Slot 1 board
9. Video card-Intel i740-854 8MB
10. Serial\Parrallel Ports-2COM\1LPT

Bios setting-PNP OS=NO
IRQs-#3 is listed as Free

Also to clarify-when I click on resources for IO read data port for ISA PnP enunmerator
no conflicts are listed-it says there is a problem with the configuration-when I click on configure manually-conflicts listed.

I am confused though-these are supposed to be "Shared" IRQs-right?









[This message has been edited by StarWatcher (edited 05-22-99).]

[StarWatcher]

Well, I figured out how to fix this configuration problem-after days of re-installing drivers http://www.sysopt.com/forum/frown.gif Here's the fix--system-device manager-Intel 82371AB\EB PCI Bus Master IDE Controller-properties-settings-set to: Both IDE Channels enabled-All better now http://www.sysopt.com/forum/smile.gif