zepper
11-20-2006, 03:48 AM
'
'
Zippy is here - Pounce !
1- Zippy HP2-6460P power supply. (These don't hang around long!) This one had a wonderful childhood in an air-filtered and power-conditioned server room with a loving tech staff to cater to its every need - neat as a pin inside and out! Conservatively rated at 460 Watts continuous with 32 Amps on the +12 rail. It's not a current design with more than half its output on the +12 rail, but it does have a strong enough +12 rail to handle most systems. Plus it's a single-rail PSU so you can really use ALL the available 12V power, unlike many split-rail units. Active PFC (power factor correction) and auto-ranging AC voltage compensation from 100-240VAC. That last makes a PSU relatively immune to AC line-side glitches short of a bad brown-out or complete dropout.
. It has the standard EATX 24-pin connector (aka EPS12V) (a 24 to 20-pin adapter is available if needed) and the 2x4 +12V connector for dualie mobos as well as the P4-12V for single CPU mobos. There are 8 drive connectors, one being the floppy size. The wires are all plenty long for server cases and other large or strangely arranged cases like the original Stacker - see the Connector Diagram link below. And all the wires except for the floppy and a few sensor wires are 18 gauge. Here is a Pic (http://i52.photobucket.com/albums/g24/zepper0/hp2-6460p.jpg) in original trim.
This heavy duty, server-grade, nickel-plated beauty came with the standard fan (full speed 24/7) so it is quite noisy - fine for a server room, but I doubt it would be tolerable in a home setting or a quiet office for very long.
Connector Diagram (http://www.techimo.com/photo/data/4/hp2-pins.jpg).
Pic of one I modded before (http://www.techimo.com/photo/data/4/HP2-6460P-Mod.jpg).
. The gray around the opening is paint to protect the raw edges after cutting - this time I'll be using a nibbling tool instead of a Dremel, so the cuts will be neater - much less paint.
Linkage (http://www.zippy.com/P_product_detail.asp?lv_rfnbr=2&pp_rfnbr=1010&pcp_rfnbr=3&pp_name=&pcp_name=PS2/PS2+%20single&pcpw_rfnbr=4&pp_code=HP2-6460P) to Zippy's HP2-6460P info page.
And here's a link to the MadShrimps Review (http://www.madshrimps.be/gotoartik.php?articID=281).
. It can be yours for $55. + $8.50 priority shipping + insurance (optional, see General Terms). I'll toss in a nice power cord (if needed) and a set of mounting screws and washers (It's heavy at 5lb.-4oz. net - don't want to warp your case metal... ;) ).
. I can modify this PSU for more quietude if you want. Suggested mods: Cut out the restrictive grille seen in the pics, replace the fan with a Vantec ThermoFlo TF8025 which has integrated temp control, protect the fan with a wire finger guard, and isolate it with a Vantec silicone gasket. This fan also has a speed sensor lead so you can monitor it if you want. I'll throw in a fan extension in case you need it to monitor the fan. Mods will add $10. to the price (the parts alone are a $12.00 value). The wire finger guard will protrude from the PSU's case a bit, so you will need good clearance around the fan area in your case's PSU cutout. Or you can easily remove the fingerguard if you encounter a clearance problem. Let me know if you want this optional mod package.
------------- General Terms: -------------
Shipping will be via USPS First Class or Priority Mail (depending on pkg weight) with Delivery Confirmation service included at no extra charge. I will calculate shipping based on your ZipCode (priority only) and get the info to you ASAP. The total shipping cost will be my actual cost rounded UP to the nearest dollar.
. Insurance is optional and is $1.35 for up to $50. $2.30 from $50 to $100. -- Buyer assumes ALL shipping risk on uninsured packages.
. The item(s) will be carefully packed to arrive at your door just as it left mine!
Payment can be made by PayPal, MO, CC, PC. Any means of payment other than USPS Money Order may be delayed for clearing at my discretion. If this occurs (unlikely but for PCs), I will notify you ASAP!
. Determination of suitability for your purposes must be done prior to sale - ALL sales are Final! I will be glad try to answer any questions - PM or email me.
.bh.
Heatware= Zepper (http://heatware.com/eval.php?id=13767)
eBay = technoia
:t
'
Zippy is here - Pounce !
1- Zippy HP2-6460P power supply. (These don't hang around long!) This one had a wonderful childhood in an air-filtered and power-conditioned server room with a loving tech staff to cater to its every need - neat as a pin inside and out! Conservatively rated at 460 Watts continuous with 32 Amps on the +12 rail. It's not a current design with more than half its output on the +12 rail, but it does have a strong enough +12 rail to handle most systems. Plus it's a single-rail PSU so you can really use ALL the available 12V power, unlike many split-rail units. Active PFC (power factor correction) and auto-ranging AC voltage compensation from 100-240VAC. That last makes a PSU relatively immune to AC line-side glitches short of a bad brown-out or complete dropout.
. It has the standard EATX 24-pin connector (aka EPS12V) (a 24 to 20-pin adapter is available if needed) and the 2x4 +12V connector for dualie mobos as well as the P4-12V for single CPU mobos. There are 8 drive connectors, one being the floppy size. The wires are all plenty long for server cases and other large or strangely arranged cases like the original Stacker - see the Connector Diagram link below. And all the wires except for the floppy and a few sensor wires are 18 gauge. Here is a Pic (http://i52.photobucket.com/albums/g24/zepper0/hp2-6460p.jpg) in original trim.
This heavy duty, server-grade, nickel-plated beauty came with the standard fan (full speed 24/7) so it is quite noisy - fine for a server room, but I doubt it would be tolerable in a home setting or a quiet office for very long.
Connector Diagram (http://www.techimo.com/photo/data/4/hp2-pins.jpg).
Pic of one I modded before (http://www.techimo.com/photo/data/4/HP2-6460P-Mod.jpg).
. The gray around the opening is paint to protect the raw edges after cutting - this time I'll be using a nibbling tool instead of a Dremel, so the cuts will be neater - much less paint.
Linkage (http://www.zippy.com/P_product_detail.asp?lv_rfnbr=2&pp_rfnbr=1010&pcp_rfnbr=3&pp_name=&pcp_name=PS2/PS2+%20single&pcpw_rfnbr=4&pp_code=HP2-6460P) to Zippy's HP2-6460P info page.
And here's a link to the MadShrimps Review (http://www.madshrimps.be/gotoartik.php?articID=281).
. It can be yours for $55. + $8.50 priority shipping + insurance (optional, see General Terms). I'll toss in a nice power cord (if needed) and a set of mounting screws and washers (It's heavy at 5lb.-4oz. net - don't want to warp your case metal... ;) ).
. I can modify this PSU for more quietude if you want. Suggested mods: Cut out the restrictive grille seen in the pics, replace the fan with a Vantec ThermoFlo TF8025 which has integrated temp control, protect the fan with a wire finger guard, and isolate it with a Vantec silicone gasket. This fan also has a speed sensor lead so you can monitor it if you want. I'll throw in a fan extension in case you need it to monitor the fan. Mods will add $10. to the price (the parts alone are a $12.00 value). The wire finger guard will protrude from the PSU's case a bit, so you will need good clearance around the fan area in your case's PSU cutout. Or you can easily remove the fingerguard if you encounter a clearance problem. Let me know if you want this optional mod package.
------------- General Terms: -------------
Shipping will be via USPS First Class or Priority Mail (depending on pkg weight) with Delivery Confirmation service included at no extra charge. I will calculate shipping based on your ZipCode (priority only) and get the info to you ASAP. The total shipping cost will be my actual cost rounded UP to the nearest dollar.
. Insurance is optional and is $1.35 for up to $50. $2.30 from $50 to $100. -- Buyer assumes ALL shipping risk on uninsured packages.
. The item(s) will be carefully packed to arrive at your door just as it left mine!
Payment can be made by PayPal, MO, CC, PC. Any means of payment other than USPS Money Order may be delayed for clearing at my discretion. If this occurs (unlikely but for PCs), I will notify you ASAP!
. Determination of suitability for your purposes must be done prior to sale - ALL sales are Final! I will be glad try to answer any questions - PM or email me.
.bh.
Heatware= Zepper (http://heatware.com/eval.php?id=13767)
eBay = technoia
:t