Mother board and memory

[civic91dx]

Ok well i have had an Abit Nf7-s vr2 (http://www.newegg.com/app/viewProductDesc.asp?description=13-127-166&depa=0) with a Amd Barton 2500+ (http://www.newegg.com/app/viewProductDesc.asp?description=19-103-379&depa=0) with Corsair XMS (http://www.newegg.com/app/viewProductDesc.asp?description=20-145-427&depa=0) for about 6 months. well i was talking to my friend and he said that my ram should be runnin at 400mhz instead of 333. i told him that it is because of the cpu being 333 but he said that it wouldnt matter. right now i have my computer running at 11.5 x 189 stable. i try 200 and it wouldnt start up. my i right or wrong. Sorry i didnt know if i should post her of overclockin. oh yeah do u guys think 35*c at this speed if some good temp(are read by abit software and sandra)thanks
carlos

[Baddog]

Try 200 x 11:t
You are good to go at 35C, mine runs mine at 53c.

[civic91dx]

yeah that is with some new as5 and a thermalright slk-947u. what voltage should i run it at??

[civic91dx]

well it only liked 191 x 11. i up the voltage to 2.7 but still nuthin

[Magua]

i up the voltage to 2.7 but still nuthin

You either meant 1.7 or your increasing the wrong voltage. That CPU should be 1.650 default...don't think it has a chance at anything past 1.9ish

[Baddog]

You should be able to go 200 X 11 @ 1.75 and 2.75 on the ram@400MHZ

[Magua]

I just put my 2800+ to 200x11 at stock voltage (1.65v) Runs like a gem....tempted to push it a bit more though.

[civic91dx]

well it doesn let me go pass 189. which one is the ram voltage then bacause the one that is like 2.XX says ddr sdram voltage and then there is a chipset set one. there is a pic attach to show what im talkin about. right now i have it at 12x189 but i want that ram running at full 400
thanks
carlos

[Baddog]

Raise your CPU voltage up to 1.75 and DDR voltage to 2.75, f10 and savve....reboot...then restart....go into the bios....raise the FSB to 200 X 11..f10......reboot. Remember this is at your own risk.
But your voltage is too low to get the 200 clock.:t

PS: Keep an eye on your temps, they will go up raising the voltage up.

[porsch1909]

Originally posted by civic91dx
Ok well i have had an Abit Nf7-s vr2 (http://www.newegg.com/app/viewProductDesc.asp?description=13-127-166&depa=0) with a Amd Barton 2500+ (http://www.newegg.com/app/viewProductDesc.asp?description=19-103-379&depa=0) with Corsair XMS (http://www.newegg.com/app/viewProductDesc.asp?description=20-145-427&depa=0) for about 6 months. well i was talking to my friend and he said that my ram should be runnin at 400mhz instead of 333. i told him that it is because of the cpu being 333 but he said that it wouldnt matter. right now i have my computer running at 11.5 x 189 stable. i try 200 and it wouldnt start up. my i right or wrong. Sorry i didnt know if i should post her of overclockin. oh yeah do u guys think 35*c at this speed if some good temp(are read by abit software and sandra)thanks
carlos


the memory should only run at 333 you where right and your friend was wrong!! :D

[civic91dx]

nope it didnt start. i up the voltage and nutthin. what timin should i be runnin the timin on my ram??

[cheeseman]

that is why i don;t overclock becuase i know my temps would not like me:D