MrT
06-18-1999, 06:40 PM
Need help figuring out if this pc will accept a 400 mhz celeron. here is my info for the system it is going into. WARNING: alot of info here...but I really need help.
Thanks Guys.
____________________
Battery Lithium 3V
BIOS Intel® E28F002BXT80 2 MBit Flash EPROM
System BIOS by Phoenix
Bus PCI/ISA based system bus
66MHz maximum bus speed
Cache 32K level 1 cache
512KB level 2 cache in the Single Edge Contact cartridge
Chipset Intel® 82371AB PCI chipset (PllX4)
Intel® 82443LX PCI AGP Controller
CPU Intel® PentiumII™ processor with MMX technology
Motherboard supports any pin-compatible PentiumII™ processor up to 333MHz
I/O PC97307VUL I/O Controller
Interfaces 2 DB-9 Serial ports
1 DB-25 Parallel port
1 PS/2 keyboard port
1 PS/2 mouse port
2 USB connectors
1 DB-15 MIDI/Game port(Optional)
3 Stereo mini-jacks for Line In, Line Out & Mic (Optional)
RAM 3 168-pin DIMM sockets, upgradeable to 384MB total SDRAM
Video Options No on-board video
Audio Options Yamaha OPL3-SA3 Audio Controller (optional)
Yamaha OPL4-ML wavetable synthesizer (optional
A PS/2 Keyboard Port N DIMM Sockets
B PS/2 Mouse Port P Power Supply Connector
C Parallel Port Q Floppy Connector
D Serial Port 2 R Primary IDE Connector
E Serial Port 1 S Secondary IDE Connector
F USB Ports T CYP2275A Frequency Generator
G PCI Slots U PC97307-VUL Super I/O Controller
H Yamaha OPL3-SA3 Solder Pad (Optional) V System Configuration Jumper Block J8B2
I AGP Port W Yamaha OPL4-ML Wavetable Upgrade Module Headers (Optional)
J Battery X Flash BIOS
K 82443LX PCI AGP Controller (PAC) Y 82371AB PIIX4
L SLOT1 SEC Cartridge Connector Z ISA Slots
M Heatsink Support Base AA Front Panel Connectors (J8H2)
This motherboard utilizes the SEC slot (SLOT1), which is a staggered 242 pin Single Edge Contact slot. This motherboard is designed to be upgradable with any pin-compatible Intel® Pentium™ II processor, up to 333MHz. The cartridge has a heatsink, either full- or half-size, mounted to it, which cannot be removed without removing the SEC cartridge. The full-size heat sink is supported by the Heatsink Support Base and Top Bar, which secures the heatsink and protects the PCI chipset underneath it. If the heat sink has a fan mounted on it, the fan power supply connector must be disconnected before the SEC cartridge can be safely removed. The speed of the processor can be set by using the configuration jumper (J8B2) on the motherboard to enable Configuration Mode
____________________
I know it says it will only go up to a pentium II 333, but it says nothing about a celeron. ????Can't find any 333 pentium II's around ..if not a 400 celeron maybe a 333 celeron or something in that field???
HELP...
[This message has been edited by MrT (edited 06-18-99).]
Thanks Guys.
____________________
Battery Lithium 3V
BIOS Intel® E28F002BXT80 2 MBit Flash EPROM
System BIOS by Phoenix
Bus PCI/ISA based system bus
66MHz maximum bus speed
Cache 32K level 1 cache
512KB level 2 cache in the Single Edge Contact cartridge
Chipset Intel® 82371AB PCI chipset (PllX4)
Intel® 82443LX PCI AGP Controller
CPU Intel® PentiumII™ processor with MMX technology
Motherboard supports any pin-compatible PentiumII™ processor up to 333MHz
I/O PC97307VUL I/O Controller
Interfaces 2 DB-9 Serial ports
1 DB-25 Parallel port
1 PS/2 keyboard port
1 PS/2 mouse port
2 USB connectors
1 DB-15 MIDI/Game port(Optional)
3 Stereo mini-jacks for Line In, Line Out & Mic (Optional)
RAM 3 168-pin DIMM sockets, upgradeable to 384MB total SDRAM
Video Options No on-board video
Audio Options Yamaha OPL3-SA3 Audio Controller (optional)
Yamaha OPL4-ML wavetable synthesizer (optional
A PS/2 Keyboard Port N DIMM Sockets
B PS/2 Mouse Port P Power Supply Connector
C Parallel Port Q Floppy Connector
D Serial Port 2 R Primary IDE Connector
E Serial Port 1 S Secondary IDE Connector
F USB Ports T CYP2275A Frequency Generator
G PCI Slots U PC97307-VUL Super I/O Controller
H Yamaha OPL3-SA3 Solder Pad (Optional) V System Configuration Jumper Block J8B2
I AGP Port W Yamaha OPL4-ML Wavetable Upgrade Module Headers (Optional)
J Battery X Flash BIOS
K 82443LX PCI AGP Controller (PAC) Y 82371AB PIIX4
L SLOT1 SEC Cartridge Connector Z ISA Slots
M Heatsink Support Base AA Front Panel Connectors (J8H2)
This motherboard utilizes the SEC slot (SLOT1), which is a staggered 242 pin Single Edge Contact slot. This motherboard is designed to be upgradable with any pin-compatible Intel® Pentium™ II processor, up to 333MHz. The cartridge has a heatsink, either full- or half-size, mounted to it, which cannot be removed without removing the SEC cartridge. The full-size heat sink is supported by the Heatsink Support Base and Top Bar, which secures the heatsink and protects the PCI chipset underneath it. If the heat sink has a fan mounted on it, the fan power supply connector must be disconnected before the SEC cartridge can be safely removed. The speed of the processor can be set by using the configuration jumper (J8B2) on the motherboard to enable Configuration Mode
____________________
I know it says it will only go up to a pentium II 333, but it says nothing about a celeron. ????Can't find any 333 pentium II's around ..if not a 400 celeron maybe a 333 celeron or something in that field???
HELP...
[This message has been edited by MrT (edited 06-18-99).]